16 Facebook Pages You Must Follow For Patio Door Lock Repair-Related Businesses
Patio Door Lock Repairs
Over time, wear and tear can lead to lock malfunctions. There are a few basic steps you can follow to restore the security of your uPVC door.
If it's resetting the lock or cleaning the locking mechanism These simple fixes can help you make your home more secure.
Clean the Lock
Patio doors are great for letting the outdoors in while keeping out the elements. However they could pose an issue for security in the event that the lock isn't working properly. Over time, wear, tear, cold and hot weather, dirt, and debris can cause your patio door lock to become difficult to operate. With a little care you can ensure that your lock for your patio door always functions correctly.
It is important to first clean the patio door lock and all moving parts. This helps flush out any accumulated grime and coatings that could hinder the lock from functioning in the way it should. Begin by wiping all the moving parts of the lock for your patio door with a damp cloth, then use a scouring pad or rough damp cloth to scrub any hard-to-reach parts of the door and frame that are coated with dirt. Then, wipe the entire lock with a dry cloth to remove any remaining dampness, and allow it to dry completely before using it again.
If you have a patio door that uses pin tumbler latch mechanisms You can apply lubrication to the lock by applying powdered graphite to the key or by using an lubricant based on Teflon such as WD-40 Multi-Use Product. This type of lubricant is able to be applied easily and does not dissolve over time. If you're unable to find a suitable lubricant, you might try using a pencil with a thick tip. Insert the pencil in the lock, and shake it around to spread the graphite.
Regular maintenance is also required to keep the tracks of sliding patio doors clear of dust, dirt and debris. These tracks are especially susceptible to snow, ice and other debris that can cause them get stuck or to bind. This could make it difficult for your patio door to open and close.
Sliding patio door track rails and rollers can be cleaned by removing any weather stripping that is damaged or dirty, cleaning them, then installing it. The rollers of patio doors can be cleaned and sprayed down with an oil that is non-stick.
Lubricate the Moving Parts
uPVC French Doors, like sliding patios, are operated with 3 to 4 or sometimes, 5 points locking mechanisms. They include the handle and lock cylinder that is operated with a key. They also require maintenance, specifically lubrication on the moving parts. This can be done with a thin oil but not WD40. This should be done at least once per year.
If hinges that are sagging aren't the cause, the door could be misaligned and catching or striking the strike plate's hole in the frame. The solution is to remove the strike plate and then use an abrasive chisel, which will enlarge the mortise that it rests in. This allows the latch to sit perfectly in the hole and avoids rubbing or catching on the frame.
When the cylinder is out of the way and out of the way, measure its width using an object or a piece of wood that can fit into the gap between the adjustment screw and the lock. The outer dimension is the distance from the outside of the door to the center of the cylinder, while the inner dimension runs from the center of the adjustment screw until the end of the cylinder.
Check the lock's width
If your patio door latch is difficult to turn even after oiling and cleaning it could be because it's not aligned with the strike plate. Verify that the door is in balance and whether the hinge screws are tight However, in many cases, moving the strike plate up or down could fix the problem.
Most of the time, the issue occurs when the lock's strike is too small for the latch to engage. In this instance, you can widen the opening with the hammer and chisel. Then, test the latch to ensure it does not rub against the jamb frame of the door or get caught on it.
Before you purchase a replacement lock, first determine the mortise type of lock you currently have. sliding patio door lock repair can be done by looking at the faceplate and noting whether it is square or round. Take a look at each screw hole on the current lock and note the size. This information will allow you to find an alternative lock that is exactly the same width and will fit in the hole that you already have.
In addition to identifying the current mortise lock, you'll also want to inspect it for any nicks or bends that may need repairing. A badly bent or damaged latch is more likely than one that has frequently used to break. Replace the lock if you notice signs of damage.
After you've determined the type of lock replacement that you require Now it's time to start the actual repair. Remove the old handle and spindle from your patio door, and then install the new one. Start by installing the inside handle. Align it with the spindle and then secure it in position using two screws or bolts. Install the exterior handle after the interior handle. After you've completed these steps you can test the new handles to make sure they are able to open and close with ease and that the latch catches properly with the strike plate.
Check the Strike of the Door.
The door latch and strike plate are the two components of the lock that work to ensure that the latch locks the door. If these are misaligned, the latch won't latch the door properly. Fortunately, this issue is usually easy to correct.
First, check the strike plate's receiving holes to make sure they are clear of obstructions such as dirt or plastic plugs. Loosen the keeper screws holding the strike plate in position. This allows it to move vertically but it will not be able to separate from the frame. Adjust the strike plate to align its holes for receiving with the latch hooks of the door latch. Once the strike plate is adjusted then tighten all screws, and test whether the door closes smoothly.
These plates are difficult to reach for homeowners with sliding patio doors. However they are vital for locking and unlocking your door. These metal plates are usually placed on the top and bottom of the door jamb where they support the door's latch. The door latch slides onto the strike plate, and it creates a seal. If the strike plate has been damaged or rusted or not properly installed the latch may not lock the door properly.
The most common reason for an outdoor door lock to become stuck or not close is a misalignment between the latch and strike plate. This can be verified using the "lipstick" test. Apply some lipstick across the edge of the deadbolt, then cover it with masking tape. The lipstick will leave an impression when you shut the door. This will show you exactly where the latch joins the strike plate. If the mark is too high or low it is possible to alter the strike plate.
If your patio door locks for sliding aren't working correctly they could be a problem in keeping your home secure from intruders. You must resolve this issue as quickly as possible. Follow these easy steps to repair your patio door lock and restore it's functionality.